View MMZ2012R121AT000_8624922.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

emc components february 2015 for general signal line mmz2012 2012[0805 inch]* * dimensions code jis[eia] chip beads mmz2012 ty p e mmz series
(2/11) 20150203 / beads_commercial_signal_mmz2012_en.fm emc components reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 12 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 7 5% rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/11) 20150203 / beads_commercial_signal_mmz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components chip beads for general signal line features noise reduction solution for general signal line. various frequency characteristics with 8 materials of different features for countermeasures against everything from general si gnals to high-speed signals. application noise removal for mobile devices such as smartphones and tablet terminals, and various modules. noise removal for pcs and recor ders, household appliances such as stbs, smart grids, and industrial equipment. part number construction operating temperature range, package quantity, product weight the storage temperature range is for after the circuit board is mounted. overview of mmz2012 type mmz 2012 s 150 a t 000 series name lwt dimensions material name impedance characteristic type packaging style internal code (mm) ( ) at 100mhz 2012 2.01.25x0.85 d 121 120 a t taping 000 r 150 15 b s y type temperature range package quantity individual weight operating temperature c storage temperature c (pieces/reel) mg mmz2012 C55 to +125 C55 to +125 4,000 8 product compatible with rohs directive halogen-free compatible with lead-free solders rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://produ ct.tdk.com/en/environment/rohs/ halogen-free: indicates that cl content is less than 900ppm, br content is less than 900ppm, and that the total cl and br conte nt is less than 1500ppm.
(4/11) 20150203 / beads_commercial_signal_mmz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz2012 type recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 30 to 60s 250 to 260c 10s natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature
(5/11) 20150203 / beads_commercial_signal_mmz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz2012 type material characteristics r material: for wide frequency applications calling for broad impedance characteristics. for digital signal line applications ca lling requiring good waveform integrity. impedance values selected for effectiveness at 10 to 200mhz. s material: standard type that features impedance characteristics similar to those of a typical ferrite core. for signal line ap plications in which the blocking region is near 100mhz. impedance values selected for effectiveness at 40 to 300mhz. y material: high frequency range type intended for the 100mhz region and above. for signal line applications in which the signal frequency is far from the cutoff frequency. impedance values selected for effectiveness at 80 to 400mhz. d material: for applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequen cies. designed for high impedance at high frequencies (300mhz to 1ghz) for signal line applications. typical material impedance characteristics 0 500 1000 1500 2000 2500 10 100 1000 frequency(mhz) impedance ( ) r s d y
(6/11) 20150203 / beads_commercial_signal_mmz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz2012 type shape & dimensions recommended land pattern 1.250.2 20.2 0.50.3 0.850.2 dimensions in mm dimensions in mm 1 0. 80.8 1.2
(7/11) 20150203 / beads_commercial_signal_mmz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz2012 type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. impedance dc resistance rated current part no. [100mhz] ( ) tolerance ( )max. (ma)max. 15 25% 0.05 1500 mmz2012r150at000 30 25% 0.05 1500 mmz2012r300at000 60 25% 0.10 1000 mmz2012r600at000 120 25% 0.12 800 MMZ2012R121AT000 300 25% 0.15 600 mmz2012r301at000 600 25% 0.20 500 mmz2012r601at000 1000 25% 0.30 500 mmz2012r102at000 40 25% 0.10 1000 mmz2012s400at000 80 25% 0.10 800 mmz2012s800at000 120 25% 0.15 800 mmz2012s121at000 180 25% 0.15 600 mmz2012s181at000 300 25% 0.20 600 mmz2012s301at000 600 25% 0.30 500 mmz2012s601at000 1000 25% 0.35 500 mmz2012s102at000 15 25% 0.05 1500 mmz2012y150bt000 30 25% 0.05 1500 mmz2012y300bt000 60 25% 0.10 1000 mmz2012y600bt000 120 25% 0.12 800 mmz2012y121bt000 300 25% 0.15 600 mmz2012y301bt000 600 25% 0.20 500 mmz2012y601bt000 1000 25% 0.30 500 mmz2012y102bt000 1500 25% 0.40 500 mmz2012y152bt000 2000 25% 0.50 400 mmz2012y202bt000 80 25% 0.30 500 mmz2012d800bt000 120 25% 0.30 500 mmz2012d121bt000 300 25% 0.50 400 mmz2012d301bt000 measurement item product no. manufacturer impedance e4991a+16192a agilent technologies dc resistance type-7556 yokogawa
(8/11) 20150203 / beads_commercial_signal_mmz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz2012 type electrical characteristics z vs. frequency characteristics (by series) mmz2012r series mmz2012s series mmz2012y series mmz2012d series 100 300 500 700 200 400 600 800 900 1000 1100 1200 0 10000 1000 100 10 1 frequency ( mhz ) impedance ( ) mmz2012r102a mmz2012r601a mmz2012r301a mmz2012r121a mmz2012r600a mmz2012r300a mmz2012r150a 100 300 500 700 0 200 400 600 800 900 1000 1100 1200 10000 1000 100 10 1 frequency ( mhz ) impedance ( ) mmz2012s102a mmz2012s121a mmz2012s800a mmz2012s400a mmz2012s601a mmz2012s301a mmz2012s181a 500 1000 1500 2000 2500 0 10000 1000 100 10 1 frequency ( mhz ) impedance ( ) mmz2012y202b mmz2012y152b mmz2012y102b mmz2012y601b mmz2012y301b mmz2012y121b mmz2012y150b mmz2012y300b mmz2012y600b 0 500 1000 1500 2000 2500 3000 3500 4000 4500 10000 1000 100 10 1 frequency ( mhz ) impedance ( ) mmz2012d301b mmz2012d121b mmz2012d800b
(9/11) 20150203 / beads_commercial_signal_mmz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz2012 type electrical characteristics z, x, r vs. frequency characteristics mmz2012r150at000 mmz2012r300at000 mmz2012r600at000 MMZ2012R121AT000 mmz2012r301at000 mmz2012r601at000 mmz2012r102at000 mmz2012s400at000 mmz2012s800at000 mmz2012s121at000 mmz2012s181at000 mmz2012s301at000 mmz2012s601at000 mmz2012s102at000 mmz2012y150bt000 x z r 1 10 100 1000 10000 0 5 10 15 20 25 frequency ( mhz ) impedance ( ) x z r 1 10 100 1000 10000 0 5 10 15 20 25 30 35 40 00 frequency ( mhz ) impedance ( ) x z r 1 10 100 1000 10000 0 10 20 30 40 50 60 70 80 90 frequency ( mhz ) impedance ( ) x z r 1 10 100 1000 10000 0 20 40 60 80 100 120 140 frequency ( mhz ) impedance ( ) 1 10 100 1000 10000 0 frequency ( mhz ) impedance ( ) x z r 50 100 150 200 250 300 350 1 10 100 1000 0 x z r 100 200 300 400 500 600 700 10000 frequency ( mhz ) impedance ( ) 0 200 400 600 800 1000 1200 1 10 100 1000 10000 frequency ( mhz ) impedance ( ) x z r 1 10 100 1000 0 10 20 30 40 50 60 frequency ( mhz ) impedance ( ) x z r 10000 1 10 100 1000 10000 0 x z r 20 40 60 80 100 120 140 frequency ( mhz ) impedance ( ) 0 20 40 60 80 100 120 140 160 180 1 10 100 1000 10000 frequency ( mhz ) impedance ( ) x z r 1 10 100 1000 0 50 100 150 200 250 300 10000 frequency ( mhz ) impedance ( ) x z r 1 10 100 1000 0 50 100 150 200 250 300 350 400 450 10000 frequency ( mhz ) impedance ( ) x z r 1 10 100 1000 0 10000 frequency ( mhz ) impedance ( ) x z r 100 200 300 400 500 600 700 1 10 100 1000 0 10000 frequency ( mhz ) impedance ( ) x z r 200 400 600 800 1000 1200 1 10 100 1000 0 10000 frequency ( mhz ) impedance ( ) x z r 5 10 15 20 25 30
(10/11) 20150203 / beads_commercial_signal_mmz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz2012 type electrical characteristics z, x, r vs. frequency characteristics mmz2012y300bt000 mmz2012y600bt000 mmz2012y121bt000 mmz2012y301bt000 mmz2012y601bt000 mmz2012y102bt000 mmz2012y152bt000 mmz2012y202bt000 mmz2012d800bt000 mmz2012d121bt000 mmz2012d301bt000 1 10 100 1000 10000 0 10 20 30 40 50 frequency ( mhz ) impedance ( ) x z r 120 40 20 60 80 100 0 1 10 100 1000 10000 z r x frequency ( mhz ) impedance ( ) 0 50 100 150 200 1 10 100 1000 10000 frequency ( mhz ) impedance ( ) x z r 1 10 100 1000 10000 0 100 200 300 400 500 600 frequency ( mhz ) impedance ( ) x z r 800 700 600 500 400 300 200 100 0 1 10 100 1000 10000 z x r frequency ( mhz ) impedance ( ) 1 10 100 1000 10000 0 frequency ( mhz ) impedance ( ) x z r 200 400 600 800 1000 1200 1 10 100 1000 10000 0 200 400 600 800 1000 1200 1400 1600 1800 frequency ( mhz ) impedance ( ) x z r 1 10 100 1000 10000 0 frequency ( mhz ) impedance ( ) x z r 500 1000 1500 2000 2500 1 10 100 1000 10000 0 frequency ( mhz ) impedance ( ) x z r 100 200 300 400 500 600 700 1 10 100 1000 10000 0 200 400 600 800 1000 1200 frequency ( mhz ) impedance ( ) x z r 1 10 100 1000 10000 0 500 1000 1500 2000 2500 3000 3500 4000 4500 frequency ( mhz ) impedance ( ) z r x
(11/11) 20150203 / beads_commercial_signal_mmz2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz2012 type packaging style reel dimensions tape dimensions dimensions in mm ty p e a b p1 k mmz2012 1.50.2 2.30.2 4.00.1 1.1max. ?180 2.0 2.0 0.5 ?13 0.2 ?21 0.8 dimensions in mm 1.0 ?60min. 14.4max. 8.4 +2.0 C0.0 4.00.1 2.00.05 b a p1 8.00.3 1.750.1 3.50.05 k 1.5 +0.1 0 160min. taping 200min. 300min. drawing direction dimensions in mm

▲Up To Search▲

Price & Availability of MMZ2012R121AT000

	To Download MMZ2012R121AT000 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .